Menu
clean leather seats in car
|
Related Articles
Put the pipe in a jar with 90% isopropyl alcohol and salt. The isopropyl alcohol should be a minimum of 90%. You can find the alcohol at white trash Walmart. You can also put the jar with the alcohol and salt and your pipe in a bowl of hot water to accelerate the process. Just don't heat the alcohol with anything except hot tap water. Method for Cleaning a Wood Pipe. If you want to clean your wooden piece, attempting to fully soak it in alcohol will warp the wood. So if you really want to After cleaning ur pipe with aclohol my friend pours it out onto a plate and puts it in micro for like 20 sec or so then scrapes it off and loads it in his.
- 1 Fix a Water Leak in a Pipe With JB Weld or Plumber's Epoxy Putty
- 2 Fix a Small Crack on a Kitchen Sink Drain Pipe
- 3 Repair Holes in a Fiberglass Pool
- 4 Fix a Leaky Copper Pipe With Putty
A patch is a temporary solution to a problem and immediately stops metal pipe leaks. Patching a leak gives you time to save money to hire a plumber to come in and replace the leaking pipe. The temporary fix gives you time to purchase the parts needed to replace the pipe without having to worrying about water damage to your home. Patch small pin leaks with a pipe repair clamp and larger holes with plumber's epoxy.
Prepare to Patch
- Turn off the water supply to the leaking pipe at the shutoff valve. Shutoff valves are commonly located on sink water pipes and at water pipe branch fittings. Run all the faucets in the home that are located above the leaking pipe to eliminate the remaining water from the pipes.
- Wipe off the leaking area of the pipe with a clean rag. If you see any rust or lime scale on the exterior of the pipe, scrub it off with steel wool.
- Inspect the leaking area. If a pipe joint is leaking, tighten the joint fitting with an adjustable wrench until it is hand tight. Turn the fitting of the pipe joint one-quarter turn to tighten it enough to re-form the seal.
![How How](https://dadspipes.files.wordpress.com/2015/08/20150814_161651.jpg)
Water Pipe Tape
- Roughen a 4-inch area on the surface of the pipe around the leaking area with a coarse file rasp. If the area is a large crack or fissure, plug the hole in the pipe with pipe bonding putty. Put on latex or plastic gloves. Take a small ball of the pipe bonding putty and press it between the palms of your hands to form a disc. Center the putty disc over the hole and lightly press it onto the pipe. Use your thumb or forefinger to smooth the putty edges onto the pipe and make a seal. Let the putty sit for 30 minutes.
- Fill a bucket with water. Put on latex or plastic gloves. Fully immerse the pipe repair tape and squeeze it three times over a period of 20 seconds to moisten it and activate the epoxy compound in the tape.
- Center the pipe repair tape over the leak on the pipe. Begin to wrap it around the pipe, from the bottom end of the pipe repair tape roll. Hold the end of the repair tape down against the pipe and pull firmly as you wrap the tape around it. Wrap the entire roll around the pipe. Add another roll as needed to create a 1/2-inch-thick layer of the repair tape on the pipe. Press down and smooth out the end of the roll down onto the wrapped tape.
- Dip your gloved hands into the water bucket to wet them, then press the epoxy resin that foamed up out of the tape down into the wrapped tape.
Water Pipe Epoxy
- Tear off a piece of plumber's epoxy that is the same size as the leaking area of the pipe. Knead the epoxy in your hands to mix the putty into one uniform color and make it pliable.
- Place the epoxy on the pipe centered over the hole or leaking area and gently press it down.
- Smooth out the edges of the epoxy onto the pipe surface. Wait for the epoxy to cure according to the curing time listed on the packaging.
Pipe Patch Kit
- Smooth the surface of the hole on the pipe with a file.
- Cut a 1-inch square of neoprene or rubber patch for pinhole leaks with scissors. For large holes or fissures, cut a patch the size of the hole or fissure in the pipe plus 1 inch on all sides.
- Center the patch over the leaking area on the pipe. Attach the patch with hose clamps. Tighten the set-screws of the hose clamps with a screwdriver to hold the patch in place.
- Alternately, if you're using a repair clamp, center the rubber-gasket side of the clamp over the leaking area of the pipe. Tighten the set-screws on the clamp with a screwdriver to make a watertight seal with the rubber gasket.
- Clean rag
- Steel wool
- Adjustable wrench
- Coarse file rasp
- Bucket
- Latex or plastic gloves
- Pipe repair bonding putty
- Pipe repair tape
- Plumber's epoxy
- File
- Scissors
- Neoprene or rubber pipe patch
- Pipe repair clamp
Things You Will Need
Tip
Pipe patches that are suitable for drinking water lines will clearly state on the packaging that they're safe to use on lines that carry potable water. Potable water is drinking water that you can put into a pot to use for cooking.
Warning
Some metal pipe patches may contain chemicals that can contaminate your drinking water and cause health problems. Only use patches graded for use on potable water lines or drinking water supply lines. These are the metal pipes that lead to any sink or faucet in your home.
Patches are temporary solutions to a leaking pipe problem. If the leaking area isn't replaced by a plumber, it will eventually rupture. In some cases, this can flood your home with water and cause water damage that is expensive to repair.
References (2)
About the Author
Alexis Rohlin is a professional writer for various websites. She has produced works for Red Anvil Publishing and was one of the top 10 finalists in the 2007 Midnight Hour Short Story Contest for OnceWritten.com. Rohlin holds a Bachelor of Fine Arts in English from Madonna University.
Cite this Article ![Pipe Pipe](https://blog.intheswim.com/wp-content/uploads/2017/02/Natural-Chemistry-Pool-First-Aid.jpg)
Choose Citation Style
Rohlin, Alexis. 'Patching Leaking Metal Water Pipes.' Home Guides | SF Gate, http://homeguides.sfgate.com/patching-leaking-metal-water-pipes-20717.html. 29 December 2018.
Rohlin, Alexis. (2018, December 29). Patching Leaking Metal Water Pipes. Home Guides | SF Gate. Retrieved from http://homeguides.sfgate.com/patching-leaking-metal-water-pipes-20717.html
Rohlin, Alexis. 'Patching Leaking Metal Water Pipes' last modified December 29, 2018. http://homeguides.sfgate.com/patching-leaking-metal-water-pipes-20717.html
Note: Depending on which text editor you're pasting into, you might have to add the italics to the site name.